GeekVape Zeus X RTA Review

Today I have an interesting guest who has reincarnated many times already and has a decent army of fans. Frankly, the last experience with his brethren happened to me quite a while ago, but I still try to compare them a bit. 

GeekVape Zeus X RTA Case material: stainless steel Atomizer type: RTA Capacity: 3.5 / 4.5ml Diameter: 25mm landing / 26.5mm maximum / 29mm on bubble glass Height: 43mm with dark drip type / 39mm without drip type Connector: 510, pin gold-plated Weight: 61g Color: see photo below Package contents – Zeus X RTA – 2pcs pre-wound spirals

– Cotton 2 laces 
– Allen 
key – Wrench screwdriver 
– Spare orings 
– Spare screws – Spare 
– Additional 810th Drip type 
– Adapter for 510th Drip types 
– User manual 
– Certificates, etc. I can not say about the set – it is just gorgeous, there is everything for the start, as well as for a little customization of the tank. Our guest looks decent. I do not even know why, but I liked it. It is likely that the impression is now smoothed round, in contrast to its predecessors, the geometry of the lid, as well as a very original preset drip type.

Dimensions wide decent, especially with bubble glass. And without it, when you hold it in your hand, it seems that it is something solid, powerful. Accordingly, the weight of the device turned out to be somewhat large. On lightweight mods, it may outweigh, although with dunobochnikami, which he most likely is designed for is unlikely to happen. Drip two types, both 810th landing. One is made of the dolrin, the second of the ultem, the latter is slightly higher. Although I liked the dark version more visually, it collects much more condensate than its translucent counterpart. The adapter for the 510th copies was also put, but I don’t know why it is needed here.

The cover is quite massive, the locking mechanism is half-turn. It is easy to get into, for convenience, there are non-acute risks. Under the cover are two small holes for refueling. You see how much they are recessed below the edges of the tank, and inside the shaft rises, therefore, the nozzles of the bottles do not penetrate directly into the holes, hanging above them. I will not say that this creates difficulties in refueling, but probably it was not worth lowering them so low. Naturally, the construction cover is to blame. Ring tightening adjustment with a stopper, it is removable. The move is pretty tight though there are risks. Therefore, by accident, adjusting the airflow, you can open the cover. I will not mention this moment as critical, because it happens quite rarely, at least for me. The size of the air intake holes 13 x 2mm.

Electronic Cigarettes Wholesale,Vape Wholesale and Distribution – Ave40

The delay turned out sooo free, I covered it a little more than half. And I would like to cover up more, but then the steam is very hot and the taste is lost. The capacity of the tank is not the greatest, it can be increased due to the complete glass bubble. And even with him, the tank eats slush decently, and it’s still clear two spirals. As you understand, the non-spill-based constructive of our hero obliges him to have a double dome. Internal processing of the latter under the cone. The diameter of the mine is approximately 7.5mm, and the diameter of the dome at the base is 17mm. It is inserted into a larger one and is fixed by an oring, but remains movable for rotation of the base when it is wound. On its side there are three rows of holes, so that the bottom two rows are beating on the coyle from the side, and the top is obtained as if from above – at an angle to the deck.

I think many zevovody now again begin to lament about the extra holes. In part, I agree – in the top row, it seems, it was better to leave not five, but three holes. Why not remove them at all, I do not know, I also thought so on the first photo, but somewhat changed my mind after the tests. More on that later. Deca is quite simple and almost easy to maintain.

Two racks rise above it to fix the two spirals correctly. The screws are pre-installed under the slot, another two spare sets – one of them for the complete hex. The distance between the corresponding screws is 7mm. Under the racks there are special grooves in order to cut the coil legs after installation. Yes, it can be done, but, firstly, it is not particularly convenient, and secondly, the stings of your nippers should be very sharp and thin in order to crawl into this gap. Near the racks you can see two keys that are combined with the grooves on the inner dome and rotate it when winding the base.

It is a tricky business to fuel the tank, but there is one thing. It is inconvenient to mark the airflow holes, because if you tighten it, you won’t see a damn thing through the small holes. Therefore, it will have to be applied from the side, since it will be necessary to do this once or twice. Again, the design of the dome is limited to adjusting the position of the spiral. The bottom airflow holes peel above the very top of the pillars, then it turns out that the top beats exactly on top of the helix. It is impossible to make the latter fall even on the center of the spiral, for the dome is already beginning to narrow. You can, of course, push the coils closer to the center of the deck, but then they are significantly removed from the blower. In short, I chose a neutral position, in which the lower to the bottom, central to the center, and the upper, whatever one may say, is the captain on top – obvious, isn’t it?)

The holes for laying wool seemed to me average, and I decently combed the cotton. However, after that, he even walked into them a little. So here, as it seems to me, everything is fine – there is enough space for cotton from two spirals. Naturally, you will have to leave rather long ends, since the pillars rise significantly from the bottom of the base. At the same time, I did not observe absolutely any zhizhezhubaniya, perhaps between puffs, the cotton wool is moistened not particularly quickly – uncritically.

The taste of the tank is decent, I will immediately calm the admirers of Zeus – as it seems to me, this is the most successful copy in the line, including the taste transfer. He lays out the ingredients for the liquid, of course, not like a dripka, but it is understandable. Moreover, the dilution of steam is almost not felt. That is why I made a reservation about the extra holes in the dome. It seems to me that they almost do not interfere, but probably without them the taste was a little brighter, but the bulk probably suffered, because here it is decent. At the same time, the tank lid is not heated at all (thanks to the non-spill constructive structure), so you can not worry about your lips when using a low-profile complete drip type. Pin is gilded and performs decently. Impressions of use

I quite liked the tank, although lately I have moved away from the use of double-spiral specimens. It is assembled perfectly – there is absolutely nothing to complain about. Deca is still easy to maintain, and the equipment is cool. Well, traditional cherries for him are non-spill constructive, design and decent taste transfer. 

  • Non-spill constructive
  • Design (IMHO)
  • Decent taste transfer
  • Equipment
  • Price

Click Here Ave40  For Vape Wholesale Cooperation.

Now It’s Available: GeekVape Zeus X RTA
Hot Sale Recommendation:

Vaporesso Aurora Play Zippo Pod Starter Kit

Vladdin Eden Vape Pod System Kit

Smok Novo 2 Pod System Kit

Voopoo Drag Nano Kit

Vaporesso Gen TC Box Mod

Vape Wholesale & buy Electronic Cigarettes online in Bulk. 2m*1i9y0a7j*

Quality Vape Products, Trusted Vape Wholesale Supply by VapeShops Owners.



Vaptio Spin IT Vape Pen Kit Review

Vaptio has released the Spin It Starter Kit for newbies. The All-in-one device got a rotating tip, a 1.8 ml cartridge and a built-in 650 mAh battery.

On April 17, Vaptio introduced a new Spin It Starter Kit on Instagram. Compact AIO device made of aluminum alloy; with a flattened profile and rounded edges. The driptip and the cartridge with the evaporator were implemented as a separate, rotating through 180 ° module. They gave the opportunity to hide the driptip inside, providing protection from dirt. Also saved the device from accidental switching on – the evaporator loses contact, being on the opposite side. Sideways provided a window to control the level of liquid in the tank. On the front side there is an oval fire button and a charge indicator on the bottom. At the bottom put a USB port.

The device works with branded cartridges with a volume of 1.8 ml and evaporators at 1 ohm. Power is provided with a built-in 650 mAh battery, charging via USB. Output power is 15 watts.

The Spin It Starter Kit comes with two cartridges, a drip tip, a USB cable, and an instruction sheet.

Main characteristics: 

  • Size – 133 by 22 by 18 mm
  • Material – Aluminum alloy
  • Tank capacity – 1.8 ml
  • Power from 10 to 15 watts
  • Built-in 650 mAh battery


Constructed of anodically oxidized aluminum alloy

Portable pen-style size with the compact design

Implements unique spinnable drip tip design

Give you more hygienic and safer vaping experience

Easy top refill system & Leak-proof engineering

Japanese organic cotton coil for excellent flavor

Adopts smooth-tech flavor optimization technology

Package Included:

1x Spin It Mod

2x Spin It Tank (one pre-installed)

1x Drip Tip

1x USB Cable

1x User Manual

Click Here Ave40  For Vape Wholesale Cooperation.

Now It’s Available: Vaptio Spin IT Vape Pen Kit
Hot Sale Recommendation:

Vaporesso Aurora Play Zippo Pod Starter Kit

Voopoo Alpha Zip TC Kit

Vladdin Eden Vape Pod System Kit

Voopoo Drag Nano Kit

Smok Novo 2 Pod System Kit

Vape Wholesale & buy Electronic Cigarettes online in Bulk. Quality Vape Products, Trusted Vape Wholesale Supply by VapeShops Owners.




ThunderHead Creation Tauren One RTA Review

Finally, we have really interesting news – there are so few of them lately) Probably, heeding the wishes of its fans, THC released a single-spiral tank, based on its past developments. Without unnecessary snot familiar. 

ThunderHead Creations Tauren One RTA 
ThunderHead Creations Tauren One RTA - From Drip to Tanks ...
Case material: stainless steel 
Atomizer type: RTA 
Capacity: 2 / 4.5ml 
Diameter: 24mm 
Height: 41mm with Drip type 
Connector: 510, pin gold-plated 
Weight: unknown 
Color: see photo below 
ThunderHead Creations Tauren One RTA - From Drip to Tanks ...
contents – Tauren One RTA 
– key -hex 
– screwdriver 
– spare oring
– spare screws 
– spare “glass” 
– user manual 
– carrying bag with key ring 
– aluminum “box” with stand 
ThunderHead Creations Tauren One RTA - From Drip to Tanks ...
Appearance is quite neat, the design is made in a corporate style, therefore, our visitor does not have to be recognizable. 
ThunderHead Creations Tauren One RTA - From Drip to Tanks ...
We should also mention the dimensions – the tank is quite compact. I suppose fans of the brand will certainly appreciate this fact. 
ThunderHead Creations Tauren One RTA - From Drip to Tanks ...
From the start, the developers offer six design options at once – not bad. In this regard, the manufacturer has never had problems – there are not any now. 
ThunderHead Creations Tauren One RTA - From Drip to Tanks ...
Drip type is made of ultem, branded hoop at the base, landing 810th. The cover on the screw fixation, the thread is not long, there are risks. Under it a decent size filling holes.
ThunderHead Creations Tauren One RTA - From Drip to Tanks ...
The capacity is small, but the reviewers have already “shown” that in fact it is one and a half times as large as it was declared. In addition, the bundle includes a bubble “glass”, made for some reason from plastic, which will increase the capacity to 4.5 ml. 
ThunderHead Creations Tauren One RTA - From Drip to Tanks ...
By the way, the novelty comes in an aluminum cylinder, the base of which is a stand for atomizers with a 510th connector. 
ThunderHead Creations Tauren One RTA - From Drip to Tanks ...
ThunderHead Creations Tauren One RTA - From Drip to Tanks ...
Deca brand admirers should be familiar even by touch. This is a complete copy of Tauren Solo RDA . 
ThunderHead Creations Tauren One RTA - From Drip to Tanks ...
Literally a few words about it – the deck is deck-free, designed for fixing one helix, and wound in any direction. 
ThunderHead Creations Tauren One RTA - From Drip to Tanks ...
For blowing here there is still a sieve of 28 holes in the answer. Half of them blow a spiral from below, the remainder is equally divided on the sides.
ThunderHead Creations Tauren One RTA - From Drip to Tanks ...
Places for cotton left decently, limiters are available. In addition, on the walls of the “mines” for cotton, special grooves are made to better feed with liquid. 
ThunderHead Creations Tauren One RTA - From Drip to Tanks ...
The adjustment of the blower is implemented in a standard way – a rotating ring with risks. 
ThunderHead Creations Tauren One RTA - From Drip to Tanks ...
Pin is gilded and stands out enough. 
ThunderHead Creations Tauren One RTA - From Drip to Tanks ...
Price $38.8
ThunderHead Creations Tauren One RTA - From Drip to Tanks ...
ThunderHead Creations Tauren One RTA - From Drip to Tanks ...

Click Here Ave40  For Vape Wholesale Cooperation.

Now It’s Available: ThunderHead Creation Tauren One RTA
Hot Sale Recommendation:

Vaporesso Aurora Play Zippo Pod Starter Kit

Voopoo Alpha Zip TC Kit

Vaporesso Gen TC Box Mod

Voopoo Drag Nano Kit

Voopoo Drag 2 Platinum 177W TC Box Mod

Vape Wholesale & buy Electronic Cigarettes online in Bulk. Quality Vape Products, Trusted Vape Wholesale Supply by VapeShops Owners.



The rectangular shower drain installation process.

It really never matters if you are renovating your house or not. A rectangular shower drain is always placed in all modernized bathrooms. It is not that hard to install a linear shower drain, especially the rectangular shower drain. It is also advised to first read the installation manual that comes along with the instrument before attempting to start working on the drains. If possible hire a professional to carefully place the drains for you because they know the rules to follow. The following are steps followed in the process of installing the drains.

Choose the best place to put up your drain

rectangular shower drain can be placed in for different ways. One, it can be wall mounted (either three-sided or one-sided), the second way is floor mounting- in the middle of two walls or freely on the floor. The model of the drain should be suitable for the place you want to place it. Most importantly, all the floors need to be sloping toward the channel in order to pass water no matter where the drain is placed. This aims to avoid water flooding in the bathroom because of accumulated water.

Prepare the area you plan on working on

Shower Floor Drain
Rectangular Shower Floor Drain

You should first make sure that the floor and the work area you are using is clean and presentable. Avoid getting filth and debris into the shower drain during the assembly process before you start the installation. The rectangular shower drain is protected by the use of a folded pre-assembly membrane or a cloth. Make sure you discuss the assembling process and what it entails with your tiler. Afterward, when the assembling process is over, give ample advice to the tiler on how to accommodate the drain while he works.

Make your calculations on how high the shower drain should be

Before you start your installation process, make sure you know the height of the shower drain. Be certain to keep the tiles 1mm higher than the edge of the drain so as to ascertain that the water will drain optimally. When you are determining the total depth consider the thickness of the tile, adhesiveness of the tile and levelling layer.

Put the built-in set in place

The built-in set will need to be properly placed after you create optimum space for the shower drain. After you place the built-in set, you will need to align and level it. Use the height adjustable legs to do the aligning and the levelling part of work. You should also be aware that the wall models always come together with special mounting used for the application of the shower drain on the wall.

Make a connection of the rectangular shower drain with the drainage pipe

Rectangular Shower Drains Brass
Rectangular Shower Drains Brass

The recommended diameter for replacing the drainage pipes is 50mm or less. This usually happens during the renovation of a bathroom where a shower tray needs to be put in place. You first need to put together the rectangular shower drain and the drainage pipe. Ensure that the drainage pipe is sufficiently slope. The only thing left to do is to slide the drain into the connector. Ensure to check the tightness of the drain and the connection to the sewerage system.

From there onwards, you should create a sloped floor, work on waterproofing the shower drain. You should also remember to replace the tiles in the bathroom and to seal the drain. The grate cover can be placed later on. The rectangular shower drain is therefore perfectly placed.

Shower Drains – Plumbing Parts & Supplies – Ferguson
Items 1 – 24 of 212 – Shop for Shower Drains at Ferguson. Ferguson is the #1 US plumbing supply company and a top distributor of HVAC parts, waterworks …

Joyetech eRoll Mac Portable Charging Case Review

Very interesting new product from the company Joyetech called eRoll Mac BatteryThe article will talk about 2 options for configuration. We will not torment, rather in the review!



On sale there are two versions of the device:

– Simple whale: eRoll MAC Battery, eRoll MAC Cartridge, manual, cable for charging.

– Advanced whale (in the near future will go on sale): eRoll MAC Portable Charging Case, eRoll MAC Battery, 3 eRoll MAC Cartridge, manual, charging cable, carrying case.



Height: 100 mm, 
Diameter: 9.2 mm, 
Weight: 17.3 g


Technical specifications

Battery capacity: 180 mAh, 
Tank volume: 0.55 ml, 
Evaporator resistance: 1.5 Ohm, 
Declared charging time: 30 minutes, 
Output voltage: 3.7 V.


E-cigarette review

In 2014, JoyeTech introduced the first version of the device, called eRoll-C. In general, the whale has not changed much, only together cartridge cartridges use clearomizers with evaporators on ceramics.


The electronic cigarette received a metal frame and an outer plastic casing. The device is sold in three colors: gray, black and red. A atomizer with a 1.5 Ohm non-replaceable vaporizer is used as an atomizer.


Drip-type is made of plastic and wound on the duct with a thread. Additionally, it is the top cover of the filling.


Due to the total diameter of 9.2 mm, the hole is rather small. Therefore it is necessary to use bottles with a thin spout. The volume of the tank is 0.55 ml, which is very small compared to other devices.


Air is drawn in through one small hole at the bottom of the tank. Below is a 510 connector on the thread. A battery is nothing interesting. Above is a connector. The operation of the device occurs when tightening due to the air sensor. Battery capacity is 180 mAh. Below is a contact for charging or battery station use.


Battery Station Overview

The station received the same colors as the electronic cigarette. The main feature is the built-in 2000 mAh battery.


It can also act as a protective case: it can carry one cigarette assembly and two additional cartridges. On the side of the device there is a charge LED indicator, an electronic cigarette battery charge indicator and a USB type C port for charging the station itself.

The indicator is made in the form of four lights, where 4 will be lit at 75-100 percent, 3 – at 50 to 74 percent, 2 – from 25 to 49, and 1 to 24 percent. The e-cigarette indicator will turn on while charging and will go out after the process ends. To charge an electronic cigarette, it is necessary to insert it with the contact part into a special recess in the bottom.


Technical parameters of the station:

Length: 65 mm, 
Width: 115 mm, 
Height: 12 mm, 
Weight: 128.3 g, 
Battery capacity: 2000 mAh, 
Maximum charge current: 2.0 A.



The device turned out quite strange. In 2019, we get the functionality from 2014, with no significant changes to eRoll. The volume of the tank will be enough for a maximum of half a day of use, the battery will be discharged even faster. In this form, the sale of a separate electronic cigarette does not look very attractive to purchase.


The version with the battery station is already more interesting, since the kit additionally comes with two spare cartridges. As for the consumer audience can only guess. As an option – the company wanted to make a set for girls, as is the case with the first version. But everything will rest on the price: if the maximum set costs less than $ 25, the device can be watched for purchase. 

Click Here Ave40  For Vape Wholesale Cooperation.

Now It’s Available: Joyetech eRoll Mac Portable Charging Case
Hot Sale Recommendation:

Vaporesso Aurora Play Zippo Pod Starter Kit

Voopoo Alpha Zip TC Kit

Geekvape Aegis Solo TC Box Mod

Voopoo Drag Nano Kit

Vaporesso Gen TC Box Mod

Vape Wholesale & buy Electronic Cigarettes online in Bulk. Quality Vape Products, Trusted Vape Wholesale Supply by VapeShops Owners.


Smoant Pasito Vape Pod Kit Review

After POD-systems appeared on the vaping market, many vapers gladly began to use them for two reasons – compact size and the possibility of soaring liquids based on salt nicotine. But at the same time such systems have a significant drawback – the need to change the cartridge some time after use and loss of taste, and this is an additional cost. Manufacturers offer to use replaceable evaporators, but they also need to be bought with enviable regularity. But what happened to many vapers, Smoant released the Pasito Pod System Vape Kit, the first POD system in which you can use an RBA base and replaceable evaporators. As one of the vapers said when he saw this novelty, “hello Sabtank, how stylish you have become)))”, and it’s hard not to agree with that since the new device even has a completely different body, but its base very much resembles the legendary Subtank from Kanger. In this case, the vaper will receive a compact serviced POD-system that can be confidently used with liquids, both on organic and on salt nicotine.

General information

The Smoant Pasito Pod System Vape Kit is a small POD system equipped with a sufficiently capacious battery, a modern production card and providing the vaper with the option of self-replacing the evaporator or installing a serviced RBA base. The form factor in which this system is executed is no longer a novelty, as it has been used by many manufacturers, but this does not make it unattractive. An important advantage of the device is the presence of the new CO-4 Ant chip, which not only has the full set of necessary protections, but is also able to operate at different capacities depending on the type of evaporator used or the resistance of the helix. It should be noted separately that the vaper has the ability to independently regulate the airflow, thanks to which it is possible to choose the optimal mode of soaring.

Pod System Vape Kit,Wholesale Pod systems Starter Kit – AVE40


The developers of Smoant did everything to ensure that the POD system was adequately equipped, and the vaper did not have to waste time looking for evaporators or a charging cable. In a fairly original, stylized resin box you can find:

  • Battery unit Pasito mod device;
  • Cartridge Pasito cartridge (volume 3 ml);
  • Evaporator 4ohm Ni-80 coil head (MTL);
  • Evaporator 6ohm Mesh coil head (DTL)
  • USB Type-C cable for charging;
  • User’s manual.

Pasito mod device battery pack

Many vapers, just looking at the Smoant Pasito Pod System Vape Kit, will say that this is another copy of the Orion from Lost Vape. It’s hard not to agree with this, as it looks similar. This is not to say that it is quite bad, since such a form factor of devices immediately after the appearance became very popular due to its compact size, ease of use and low weight. Therefore, users of the Smoant Pasito Pod System Vape Kit will get an angular rectangular device with a lonely protruding drip-type.

The manufacturer focuses on the fact that the body is made of aviation aluminum with side panels of plastic CPR, which very much resembles the usual resin. Thanks to this, the device looks original and beautiful.

Power Smoant Pasito Pod System Vape Kit is carried out using the built-in battery capacity of 1100 mAh, which is enough for a device of this class and size. The battery is charged using the micro-USB Type-C connector with 1A current, so that the full charge time is minimal.

An important advantage of this device is the presence of the CO-4 Ant chip, which allows you to get a standard set of device protection. But the most important thing is that the CO-4 Ant chip makes it possible to set the power of the device to work – 10/13/16/20 / 25W, and for this there is a special button on the side face. Activation is performed using the “fire” button. The manufacturer claims that the chipset will allow you to get a stable voltage regardless of the battery charge level, which is good news.

Cartridge, vaporizers and serviced base

It can be immediately noted that the cartridge in the Smoant Pasito Pod System Vape Kit is quite versatile – you can screw in both evaporators and the serviced base. The process of refilling the cartridge is extremely simple – drip-type is unscrewed, and 3 ml of liquid is poured into the hole.

Interestingly implemented and blowing system. First, it is adjustable with a small lever. Secondly, the air intake occurs from above, and then it enters the evaporation chamber through a special channel, where the evaporator is blown from below. This design allows you to get quite a decent taste on liquids and organic, and salt nicotine.

But the biggest “trick” of the Smoant Pasito Pod System Vape Kit is the ability to use both removable evaporators and a serviced base. It should immediately be said that the RBA base is not bundled, so you will have to buy it separately. The manufacturer offers two options for evaporators – for DTL and MTL puffs with resistance of 0.6 and 1.4 ohms, respectively.

If we talk to the serviced base, then the vaper is waiting for two racks in which a spiral is placed horizontally. Vaper himself determines which spiral he likes, but it is important not to forget that the base is rather small, so the Triple Fused Clapton with six turns will not fit physically there, but the microcoil of 0.4 nichrome will be excellent. For cutting wool, small cuts are provided, and with it the difficulties will not arise.

Conclusions and impressions

The Smoant Pasito Pod System Vape Kit is a device that many vapers have been waiting for. It is difficult to say – this is the POD system, or the reincarnation of box mods that were popular five years ago. But the fact remains that the device will appeal to many vapers for its versatility and functionality.

Advantages and disadvantages


  • RBA bases not included;
  • Installing the helix in the serviced database is not the easiest;
  • Drip-type can not be replaced.


  • Ergonomic body;
  • Original design;
  • Ability to install power;
  • USB Type-C will allow you to quickly charge the battery;
  • Possibility of use in MTL and VED modes;
  • Blowing adjustment;
  • Replaceable evaporators and serviced base;
  • Large cartridge volume;
  • Good taste transfer.

Click Here Ave40  For Vape Wholesale Cooperation.

Now It’s Available: Smoant Pasito Vape Pod Kit
Hot Sale Recommendation:

Vaporesso Aurora Play Zippo Pod Starter Kit

OBS Cube X 80W VW Box Mod

Voopoo Alpha Zip TC Kit

Voopoo Drag Nano Kit

OUMIER Armadillo RDA

Vape Wholesale & buy Electronic Cigarettes online in Bulk. Quality Vape Products, Trusted Vape Wholesale Supply by VapeShops Owners.


Eleaf iCare Flask Kit Review

An interesting device, resembling an army flask, was released by Eleaf. This is the Pod System, called iCare Flask. The chip of the device is ease of use and quick delivery of nicotine into the body, incl. and saline .



iCare Flask battery, iCare Flask Atomizer, magnetic 510 connector, manual, charging cable.



Height: 71 mm; 
Width: 42 mm; 
Thickness: 12 mm; 
Weight: 69 g.

Battery pack overview

The mod is made of stainless steel and is available in two colors: gray and black. Mod implemented in the form of a curved jar with rounded edges. The capacity of the built-in battery is 540 mAh.


Atomizer is inserted into a special compartment and is fixed on magnets. On the side panel is a LED charge indicator. Below is a USB port for charging the device. There are no buttons on the case – the mod works automatically when tightened.

Vape Starter Kit, Wholesale E Cig Starter Kits – AVE40


Block the device is also not possible. In general, the board has modern systems of protection against low charge, low resistance, short circuit and cut-off delay in 15 seconds.

Cartridge system

As an atomizer in the whale is a small tank with replaceable ceramic evaporators. Above is a metal driptip. Additionally, it is the top cover of the filling. The diameter of the hole is small, so it is recommended to use suitable bottles with thin noses.


The flask is held on the bottom of the oring, pressed on top of the top cap. The volume of the tank was 1 ml, which is quite impressive for such sizes. Ceramic resistors of 1 Ohm are used as evaporators. No tightening adjustment – air is drawn from one small hole at the bottom of the tank. Atomizer has a standard 510 connector. To work with this whale, the tank is wound on a special magnetic spacer, which is then attached to the fashion. We found a similar system in the Eleaf iStick Basic Kit.

Who needs iCare Flask

The whale turned out to be a rather peculiar answer to modern POD systems. iCare Flask can be called the ideological successor of the iStick Basic Kit. The same implementation of the mod in the form of a stick and the use of a small tank on removable evaporators with a magnetic connector. A small air intake opening will allow you to get tight traction that is suitable for MTL lovers or beginners. Refueling is quite convenient, firing and unhygienic, as it is necessary to remove the top cover-drip tip for refueling.


The fluid level is quite easy to track due to the slot on the side of the mod. The battery capacity is only 520 mAh, so the charge will be enough for a maximum of the day of use. The board is as simple as possible in operation; actuation occurs upon tightening. Since the diameter of the mounting hole for the atomizer is still unknown, the question of using serviced atomizers remains open. Therefore, this bundle can be considered as the same POD system. Therefore, it is suitable for lovers of compact bundles and novice bathers.

Click Here Ave40  For Vape Wholesale Cooperation.

Now It’s Available: Eleaf iCare Flask Kit
Hot Sale Recommendation:

Vaporesso Aurora Play Zippo Pod Starter Kit

Dovpo Topside Dual Squonk Box Mod

Voopoo Alpha Zip TC Kit

Voopoo Drag Nano Kit

Vaporesso Luxe 220W TC Kit

Vape Wholesale & buy Electronic Cigarettes online in Bulk. Quality Vape Products, Trusted Vape Wholesale Supply by VapeShops Owners.